What are the features of the SP-565UZ?
The Olympus SP-565UZ is a 20x ultra-zoom digital camera. Its 4.6-92.0 mm f2.8-4.5 lens yields a 26-520 mm zoom equivalent in 35mm format. To support such a long zoom ratio, the SP-565UZ incorporates Sensor Shift Image Stabilization that compensates for camera shake by gyroscopically sensing camera movement and constantly repositioning the 10.0 megapixel CCD sensor, resulting in sharper images in challeninging shooting situations. Applying the Sensor Shift Image Stabilization also enables shooting at lower shutter speeds in low-light situations and using lower ISOs for better image quality.
The SP-565UZ has an option for a 13.5 frames-per-second burst mode that also features Pre-capture technology. Pre-capture starts shooting images when the shutter button is depressed halfway, saving up to 10 shots in the buffer memory but not writing them to the memory card. The stored images are refreshed continuously until the shutter button is fully depressed, at which time the sequence is saved to the memory card along with the frames captured after the shutter button is fully depressed. Pre-capture makes it possible to record moments that pass too quickly for the typical photographer to react.
The SP-565UZ offer full creative control. In addition to three auto-exposure metering modes, it allows Aperture Priority, Shutter Priority and Manual Exposure modes. In addition to standard autofocus, the camera offers Full-Time Autofocus, Predictive Autofocus, and Manual Focus options. The Macro and Super Macro modes offer extreme close-up capabilities. In Super Macro mode, the lens will focus to 0.4 inch. (At that distance, a twenty-five cent coin would fill the frame.)
The SP-565UZ can wirelessly control the Olympus FL-36R and FL-50R electronic flash units for off-camera flash illumination using its built-in flash as the flash controller.
The SP-565UZ also features a Scene mode with 25 preset scenes so settings tailored to specific shooting situations can be quickly applied. It can also record videos with and without sound at 30 or 15 frames per second.
Bright Capture technology allows shooting in low-light situations and capturing an image that's clear and bright without a flash. And with ISOs up to 6400, the camera can capture images in marginal lighting situations.
Images can be framed and played back on either the high-resolution 2.5 inch HyperCrystal LCD screen or the electronic viewfinder.
The camera uses xD-Picture Card media for removable memory. Using Olympus brand xD-Picture Card media enables the Panorama function. Panoramic images can be stitched together using the bundled OLYMPUS Master 2 software. The camera can also use microSD memory cards when using the bundled MASD-1 microSD Adapter.
What are the purposes of the different Record Modes?
Record modes allow photographers to quickly and conveniently vary the quality settings used to capture and save images in-camera. While it is possible to always shoot at the higher-quality settings and then process the images down to lower file sizes later using a computer, it may be more convenient in some situations to shoot at other than the higher-quality settings. For example, it may be preferable to shoot using a lower-quality JPEG setting when the shot is intended for use on the Internet, where small file size is more important than rich detail.
The SP-565UZ has three record modes, whose benefits and quality settings are detailed below:
- RAW is the highest-quality record mode available on the SP-565UZ, and it allows the photographer the most creative control in post-production. Images are saved to the memory card from the camera sensor with minimal image processing. Factors such as white balance, sharpness, contrast and color are unchanged so they can be modified later on a computer. Some photographers prefer to shoot RAW format all the time for all subjects, while others may shoot RAW in situations that may pose complicated exposure problems, such as wedding photography.
Each camera manufacturer has its own version of RAW tailored to its cameras; therefore, special software is required to process RAW files and convert them to other image file formats such as JPEG and TIFF. OLYMPUS Master and OLYMPUS Studio contain RAW processing and conversion software for the Olympus RAW format, whose file extension is *.orf. Third-party imaging software and operating systems may use RAW plug-ins or updates to process Olympus RAW files. Without them, they would not be able to read RAW images from Olympus digital cameras. Most photo kiosks, printers and photo labs cannot read unconverted RAW images.
- JPEG is a compressed file format. When the camera processes a captured JPEG image and saves it to the memory card, it uses algorithms to discard some of the data to make the file smaller. The process of mathematically reducing a file’s size by discarding some of its data is called compression. When the image is opened on a computer, the JPEG algorithms reconstruct the discarded data.
JPEGs are useful because their quality settings can be manipulated from the camera menu. The two factors that comprise JPEG quality are image size and compression ratio.
Image size is determined by the number of pixels in the image. Larger files are measured in millions of pixels, or megapixels. The SP-565UZ offers the following options: 10M, 5M, 3M, 2M, 1M, VGA (640 x 480 pixels) and 16:9 (1,920 x 1,020 pixels). The VGA setting is useful for shooting low-resolution images for use on the Internet in such applications as online auction Web sites. The 16:9 setting is suitable for capturing images intended for playback on a wide-screen TV.
Two compression options are available: FINE (for high-quality images with larger file sizes) and NORMAL (for standard-quality images with smaller file sizes).
- RAW + JPEG This mode saves both a RAW image and a JPEG image when an image is captured. This can be advantageous when shots are intended for use in multiple media or when the medium in which the image is ultimately to be published has not been determined.
The quality settings used to process the JPEGs in the RAW + JPEG record mode are tied to the quality settings defined for the JPEG record mode.
What is the purpose of the Scene mode?
The SP-565UZ has a Scene mode (SCN on the Mode Dial) that optimizes the camera settings for specific shooting conditions. All of the settings applied in the 25 available Scenes can also be applied by controls in the camera menu, but applying them manually can be time-consuming. In addition, amateur photographers may not have a deep enough knowledge of photography to select the appropriate settings for some situations that advanced amateur and professional photographers would employ.
What is the purpose of the Multi Fireworks Scene?
The MULTI FIREWORKS Scene allows you to take two exposures and combine them on a single frame. Pressing the shutter button once locks the exposure and captures the first image. The image is saved and displayed in the background of the LCD monitor so that it can be used as a visual reference when composing the second image. Pressing the shutter button a second time captures the second image. The two images are then combined and saved to the memory card.
After the combined shot is saved, the first image is again displayed in the background of the LCD monitor, where it can be used to create another multi-exposure shot.
What is the purpose of the Quick Shutter scene?
The QUICK SHUTTER scene uses FULLTIME AF autofocus to ensure that the subject in front of the lens is in focus at all times. This reduces shutter lag time because the camera does not have to focus when the shutter button is pressed.
Where can I find the documentation for my camera?
The SP-565UZ is packaged with a printed Instruction Manual that includes a Quick Start Guide. If lost, replacement documentation can be downloaded in PDF format by clicking here.
Adobe Reader® is required to view the PDF files. The software is available as a free download from Adobe's Web site.
What are the P, A, S and M modes on the Mode Dial? How are they used?
The P, A, S, and M modes are the Advanced Shooting modes. These are essentially non-AUTO modes that allow the photographer more creative control by enabling more control over shutter speed and f-stop settings. Briefly, the Advanced Shooting modes and their applications are as follows:
- P (Program shooting) – Allows shooting using an aperture and shutter speed set by the camera. In many respects it is similar to the AUTO mode. Unlike the AUTO shooting mode, the program shooting mode allows full access to the menu settings for greater creative control of the camera.
- A (Aperture priority shooting) – Allows the aperture to be set manually, thereby giving the photographer control over depth-of-field. This mode also uses Program Shift, so the photographer can select any aperture in the range of the lens using the up/down arrow buttons. The camera compensates for the exposure by changing the shutter speed automatically as the f-stops are changed. The Aperture priority shooting mode automatically enables the Exposure Compensation function, which is controlled by the left/right arrow buttons.
- S (Shutter priority shooting) – Allows the shutter speed to be set manually, thereby giving the photographer control over stopping action or reducing camera shake. This mode also uses Program Shift, so the photographer can select any shutter speed in the range of the camera body using the up/down arrow buttons. The camera compensates for the exposure by changing the aperture automatically as the shutter speeds are changed. The Shutter priority mode automatically enables the Exposure Compensation function, which is controlled by the left/right arrow buttons.
- M (Manual shooting) – Allows the photographer to set the shutter speed and aperture independently of each other. Program Shift is not applied in this mode. Exposure is determined by testing or by using a light meter. In the Manual shooting mode, the shutter speed is set using the up/down arrow buttons, and the aperture is set using the left/right arrow buttons. The effect of changes in the shutter speed and aperture are shown on the LCD screen or in the electronic viewfinder. The values of underexposure and overexposure are displayed in the upper right of the screen display where the Exposure Compensation values are displayed in the P, A and S shooting modes.
When the Mode Dial is set to AUTO, why are some of the menu options deactivated (grayed-out)?
In the AUTO shooting mode, the camera operates with a minimum of input from the user. Many shooting functions are controlled entirely by the camera; the photographer cannot chnage their settings. Therefore, the menu options that control those settings are deactivated (grayed-out) in AUTO mode.
The SP-565UZ has seven focusing modes. Which should I use?
With seven focusing modes, photographers have great flexibility in setting up the camera for diverse shooting situations. The following descriptions will help you determine the best mode for each shot.
- FACE DETECT: In this autofocus mode, when the camera detects a face in the image view, it displays a green outline around the face and focuses on it. FACE DETECT is capable of detecting multiple faces and averaging the autofocus.
- iESP: This is the factory default autofocus mode. The camera itself determines which subject within the screen to focus on. Even when the subject is not in the center of the screen, focusing is possible. However, since the camera has no way of knowing what the subject is, it may not select the intended subject.
- SPOT: In this mode, the camera focuses on the subject within the AF target mark, which is in the center of the frame. If the main subject is not in the center of the frame, the AF target mark can be positioned on the subject by aiming the camera, pressing the shutter button halfway to lock the autofocus on the subject and then recomposing the shot. Press the shutter button all the way down to capture the image.
- AREA: When this option is enabled, the AF target mark can be repositioned to numerous points in the frame using the arrow buttons on the four-way keypad. You can shoot at any time in this mode. Pressing the [OK/FUNC] button returns the AF target mark to the center of the image.
- MF (Manual Focus): Manual focus is set in the FOCUS MODE option in the CAMERA MENU. Manual focus can be used creatively to focus on a specific subject or during time-lapse still image shooting. When manual focus is enabled, a focusing distance scale is displayed running horizontally on the top of the LCD screen or in the electronic viewfinder. The distance setting is controlled by the left/right arrow buttons on the keypad. While focusing, the central area of the image is enlarged for more accurate focus. Pressing the [OK/FUNC] button sets the focus. Pressing [OK/FUNC] again refocuses.
- FULLTIME AF: This mode keeps the subject in front of the lens in focus at all times without having to press the shutter button halfway. The focusing time is reduced, resulting in much shorter shutter lag. Also, the subject is automatically kept in focus during movie recording.
When the QUICK SHUTTER Scene is enabled, FULLTIME AF is automatically enabled to reduce shutter lag.
- AF PREDICT: This is the SP-565UZ application of Predictive Autofocus technology. The camera observes the movement of a subject moving toward or away from the camera and predicts its position at the moment of exposure. When activated, position the AF target mark on the subject and press the shutter button halfway to engage AF PREDICT. When the moving subject reaches the desired position in the frame, press the shutter button all the way down to take the picture.
The subject I want in focus doesn't line up with the AF Frame in the viewfinder. How do I get the camera to focus on the subject?
The AFL (Autofocus Lock) function enables the photographer to prefocus on a specific subject, lock the focus and then recompose the image and shoot the picture.
- Position the AF Frame on the autofocus subject and press the shutter button halfway until the AF Lock icon () appears in the upper right corner of the LCD screen or electronic viewfinder.
- While holding the shutter button in the halfway press position, recompose the image and press the shutter button all the way down to shoot the picture.
At first this may seem to be a cumbersome procedure, but with practice it can become a fluid movement.
The automatic settings make NIGHT SCENE convenient for night shots, but I want more creative control. How should I set up the camera?
The SP-565UZ has numerous options that give the photographer extensive control over exposure factors. Creative night photography involves using the camera's manual settings.
Two accessories are essential for night photography. The first is a steady tripod or camera clamp to stabilize the camera during the long exposures involved in night photography. The other accessory is a cable release. The SP-565UZ uses the RM-UC1 Remote Cable Release (Item # 260237), which can be purchased from The Olympus Store by clicking here.
The cable release is plugged into the camera’s USB connector. The release button can be locked down for long BULB exposures.
To set the camera up for night shooting:
- Turn the Mode Dial to the M (Manual) shooting mode. In this mode the shutter speed and f-stop are entered manually—there is no auto exposure. The shutter speed and f-stop values are shown at the bottom of the LCD screen. Pressing the Exposure Compensation button changes the functions of the four-way keypad to enable the Up and Down positions to chnage the shutter speed., and the Left and Right buttons to change the aperture. The longest exposure time available in the SP-565 is 8 minutes (when the shutter speed is set to BULB and ISO is set to 64. At ISOs up to 3200, the longest possible exposure time is 15 seconds).The effects of the exposure settings are shown on the LCD screen and viewfinder.
- The remaining settings are set in the CAMERA MENU. The first setting is WB (White Balance). Because night scenes have mixed light sources, you may have to experiment by using AUTO or one of the preset WB settings to find a desirable color balance.
- ISO is also subject to testing, depending on the exposure time used. 200 or 400 ISO are good places to start.
- SHARPNESS should be set to –5. This is the minimum sharpening the camera can apply. Since night images are usually post-processed, it is best to begin with an unsharpened image because each step of post-processing of a JPEG image recompresses the image a little bit, degrading the image.
- NOISE REDUCT. should be set to ON. Long night exposures create noise and hot pixels because the sensor heats up during the exposure. NOISE REDUCT. exposes a second dark frame with the same exposure time as the original image. The camera then compares the two images and subtracts the noise and hot pixels from the first frame, thereby saving a cleaner image.
- The focus mode should be set to MF (Manual Focus) using the slide switch on the left side of the focusing barrel. This will prevent the camera from changing focus during long exposures and yield more selective focus than if autofocus were used.
It’s a good idea to keep some notes on your tests and final settings for future night shoots. Remember to reset your camera to its normal settings after your night shoot. You can also preserve your settings for future night photography by creating a My Mode profile.
How do I use the different metering modes?
The SP-565UZ provides three metering options that allow the photographer to have greater control over exposure. The metering modes are set in the CAMERA MENU. Descriptions and applications of the metering modes are detailed below:
||ESP metering is recommended for general use. The camera meters the brightness at the center of the monitor and the surrounding area separately to capture an image with balanced brightness. When taking pictures against a strong backlight, the center of the image may appear dark.|
||Spot metering measures the exposure using a very small area in the center of the monitor and can be used to meter a backlit subject. Spot metering must be used very carefully because the brightness within the area on which the metering spot is centered can dramatically influence the final exposure.|
||Center-weighted average metering provides average metering between the subject and the background lighting, placing more weight on the center of the frame. Use this mode when you do not want the light level of the background to affect the exposure value of the main subject.|
What is Exposure Compensation, and how is it used?
Metering systems in cameras measure light but do not have a way of determining what the subject matter is, so the exposure decisions the metering system makes may not always be appropriate for the subject matter. This phenomenon is called subject failure. As with Spot metering, the human touch may be required to arrive at correct exposures. Exposure Compensation allows the photographer to set up the camera to under- or over-expose in specific situations.
Exposure Compensation is enabled by pressing the Exposure Compensation button, which is the Up position on the four-way keypad on the back of the camera. The values are changed using the Left and Right positions on the four-way keypad. Exposure Compensation is disabled by setting the value back to 0.0.
The Exposure Compensation setting is displayed in the lower left corner of the LCD or in the electronic viewfinder. It can be set to under- or over-expose up to two f-stops in 1/3-stop increments.
It is important that you set the compensation back to 0.0 before shooting subjects in other conditions so the subjects will be properly exposed.
The SP-565UZ has AUTO White Balance, so why is it necessary to have white balance presets?
Having white balance presets grants the photographer more creative control. For one thing, daylight can be warm or cold. On a sunny day, early and late light has a warmer appearance than when the sun is high. The AUTO White Balance option might color correct for that warmth, thus taking away the ambience. Using the Sunny day setting will preserve that warmth. The AUTO White Balance will also diminish the red, yellow and orange colors in a sunset, so it is advisable to use the Sunny day setting when shooting sunsets.
On cloudy days, the light seems colder because the clouds absorb the warmer red and yellow frequencies of the sunlight coming from above the clouds. Therefore, there is a Cloudy day setting in the presets to record the images with a warmer appearance. Creatively, the Cloudy day preset can be used on a sunny day to give images a more “golden” appearance, or it can be used to make a sunset warmer.
The Tungsten light setting compensates for the yellowish color cast of indoor lighting and candle light. The Tungsten light setting should be used for shooting subjects being lit with floodlights, for example, for posting to an Internet auction site. Creatively, the Tungsten light preset can be used outdoors in daylight to make the images appear more blue—giving a surreal feeling of coldness and moodiness.
The three Fluorescent lamp presets provide options for different types of fluorescent lights. These presets are valuable when photographing in business and office environments. It is advisable to shoot test shots to find the correct fluorescent preset for the shooting environment before doing available light photography under fluorescent light.
With so many White Balance settings available, why and when should I use One-Touch White Balance?
There are many light sources and situations that are not covered by Auto White Balance or the other settings in the White Balance menu. Many noncontinuous light sources, such as fluorescent, mercury vapor and sodium vapor lights, do not have all of the colors of the spectrum. There are also situations in which many different types of lights are used in one environment. These do not neatly fit into what the camera firmware knows about white balance, so it is necessary to “educate” the camera about the specific light balance by shooting a white reference subject such as a white card and saving the data in the White Balance menu as a One-Touch White Balance.
The manual says that the SMILE SHOT Scene works in the shooting standby mode. How is the shooting standby mode enabled?
When the SMILE SHOT scene is selected, it automatically puts the camera into the shooting standby mode. When the camera is in the shooting standby mode, it is waiting to detect a smiling face in the frame. When the camera detects a smiling face, it automatically shoots a picture without the shutter button being pressed. If the shutter button is pressed while SMILE SHOT is enabled, the camera will shoot a picture whether or not a smiling face is detected.
When SMILE SHOT is enabled, the Self-Timer/AF Illuminator lamp is lit.
What does the Expression Edit option do?
Expression Edit provides options to slightly modify the facial expression of a person in a photo and save a copy of the changed expression to the memory card--it can change an unsmiling face to a smiling one. The option selects the largest face in a scene that is directly facing the camera, and presents four variations to choose from and save. If it cannot find a target, the display will show Face Detect Error.
How do I decide which ISO setting to use?
Think of the ISO speeds as film speeds. Low ISOs such as 64 and 100 are better-suited to situations in which there is a lot of light - outdoors scenes, for example. Higher ISOs, such as 400 and 800, would be used outdoors where there is plenty of light and fast shutter speeds are desired - sports and air shows, for example - or indoors for available light shooting. ISO 1600 or 3200 would be used where there are very low light levels, such as indoors or at night.
The AUTO and Scene modes automatically set the ISO.
How should I set up the SP-565UZ to shoot in black and white?
The SP-565UZ always shoots in color; however, a color image can be converted to a black and white or sepia tone image using options in the EDIT menu.
To convert an image to black and white or sepia tone:
- In the Playback mode, select the image to be converted.
- Press [MENU] in Playback mode, and then open the EDIT menu.
- Using the down arrow button, select COLOR EDIT and press the [OK/FUNC] button to open the COLOR EDIT menu.
- Press [OK/FUNC] to preview the conversion. The LCD will display four previews: black and white (top left window), sepia (top right), hard saturation (bottom left) and soft saturation (bottom right).
- Use the right arrow button to select the conversion mode, and then press [OK/FUNC] to apply the conversion.
The camera will write the converted image to the memory card at the same quality setting as the original image. The original image will remain unchanged.
Note: The saturation options are used to make a color copy of an image with hard or soft color saturation.
Is it possible to take time-lapse photo sequences with the SP-565UZ?
Yes, the SP-565UZ can be used for time–lapse photography. This technique is useful for photographing moving clouds, flowers opening or wildlife interacting at a feeding station.
The TIME LAPSE function is selectable from the CAMERA MENU when using the P, A, S and M shooting modes. The TIME LAPSE option enables shooting from 2 to 99 images at intervals of 1 to 99 minutes in one-minute increments.
It is recommended to use a tripod or camera clamp to position the camera for the time-lapse sequence. Because the length of a time-lapse sequence may exceed the battery life of the four AA batteries the camera holds, it is also recommended to power the camera with the C-7AU Digital Camera AC Adapter (Item: #200685-410), which is available for purchase from authorized dealers or online directly from The Olympus Store. Click here to order.
In addition, the MF (Manual Focus) mode should be used to prevent the camera from changing focus during the time-lapse sequence.
If the intention of the time-lapse sequence is to convert the images into a movie, use the VGA record mode to accomodate the quality setting a movie requires. The finished time-lapse sequence can be converted to a movie at various frame rates using third-party software such as QuickTime® Pro.
How is Shadow Adjustment Technology applied?
Shadow Adjustment Technology can be selected by pressing the button in the lower right corner of the camera back that has an icon of a backlit person. In the bottom of the LCD display SHADOW ADJ is displayed with the option set to OFF. Use the right arrow key to select the ON option, then press the OK/FUNC button to enable the Shadow Adjustment Technology (SAT).
When SAT is enabled, the camera processes a captured image so that the shadow areas are brighter, revealing more shadow detail. The option can be used to shoot backlit or three-quarter lit subjects to make them appear with less contrast in strong daylight lighting conditions. Creatively, the option can be used in any lighting situation. In travel photography, users may choose to have the option enabled at all times. As with any creative option, it is best to experiment to test applications of the feature.
Shown below are crops of the same view shot without Shadow Adjustment Technology (left) and using Shadow Adjustment Technology (right):
Shadow Adjustment Technology should not be used with the Panorama feature in the SP-565UZ, as it will only be applied to the first frame.
How does the LIGHTING FIX function work?
The LIGHTING FIX function is used to “open up” shadow areas in a saved image to show more shadow detail without making any changes to the mid-tone and highlight areas of the image.
To apply LIGHTING FIX:
- Set the Mode Dial to the Playback mode, and then select an image.
- Press the [MENU] button, and then select PERFECT FIX.
- Select LIGHTING FIX, and then press the [OK/FUNC] button. The image to be modified will appear on the LCD screen.
- Press [OK/FUNC] again.
The LIGHTING FIX function will make a modified copy of the original image with enhanced shadow detail and save it in the camera memory or on the memory card. The original image will remain unchanged.
What is the histogram?
The histogram gives the photographer feedback on the distribution of the light and dark tones in the image. When it is enabled, it is displayed on the LCD screen or electronic viewfinder in real time.
The SP-565UZ has two types of histograms. The standard histogram displays the brightness range of the camera as a graph. The left side of the graph indicates highlights (red) and the right side of the graph indicates shadows (blue). On each end of the graph is a space indicating highlight and shadow values that fall outside of the camera’s brightness range and which will have no saved detail when the image is taken. The photographer has the option of changing settings such as Exposure Compensation, Contrast, and Saturation to fit the tones within the histogram.
The SP-565UZ also has a DIRECT histogram option that displays areas in the viewed image that will be lacking detail in the saved image. Highlights with no detail are displayed in red, and shadows with no detail are displayed in blue. When the DIRECT histogram is enabled, the graph histogram does not appear as an INFO screen and vice-versa.
The camera will also show the histogram of an image in the Playback Mode. Pressing the DISP. button will change the display of the image information. One of the displays shows a thumbnail of an image, exposure information, and the image histogram.
The histograms are selected and enabled in the SETUP menu.
I shot in the RAW format and I need a JPEG image, but I'm away from my computer. How can I convert RAW files to JPEGs in the field?
The SP-565UZ has a RAW editor in the CAMERA MENU that allows the photographer to not only convert the RAW file to a chosen JPEG record mode but also to apply white balance, sharpness, contrast and color adjustments to the converted JPEG image.
To edit a RAW file in camera:
- In the Playback Mode, select the RAW image to be edited.
- Press the [MENU] button.
- Select EDIT.The display will show RAW DATA EDIT.
- Press the [OK/FUNC] button. The following options are displayed: IMAGE QUALITY, WHITE BALANCE, WHITE BALANCE COMPENSATION, SHARPNESS, CONTRAST and SATURATION.
- Apply any changes to be made, and then press [OK/FUNC]. The LCD will then display options for IMAGE SIZE and COMPRESSION.
- Select the IMAGE SIZE and COMPRESSION options, and then press [MENU] twice. The view on the LCD returns to the original image.
- Select YES and then press [OK/FUNC] to accept the changes. An edited JPEG copy of the RAW file will be saved on the memory card.
In the FLASH menu, what is the purpose of the SLAVE mode?
Even though the SP-565UZ doesn’t have a PC sync cord connector, it can be used with studio strobes and off-camera flashes equipped with slave triggers. A slave trigger will fire a flash unit when it detects another flash firing. When the SP-565UZ Flash Mode is set to SLAVE, the camera's built-in flash will fire in sync with slaved flash units.
The SLAVE function has 10 power settings so that the camera’s built-in flash can be set from a minimum flash output (1) to full-power output (10). This gives the photographer the option of using the camera flash only as a trigger for the slaved flashes or as the main light, using the slaved flashes for fill light. When Shadow Adjustment Technology (SAT) is enabled, the SLAVE option cannot be enabled.
How do I update the camera's firmware?
Complete instructions may be downloaded by clicking here.
Adobe Reader® software is required to view the file. It is available as a free download from Adobe's web site. Click here to download the latest version.
Are any firmware updates available for my camera?
Use the Update Camera function in the OLYMPUS Master 2 software packaged with your digital camera to find out whether firmware updates are available for your model. An Internet connection is required to perform the operation.
For detailed instructions on how to update the camera's firmware, click here.
Note: If multiple firmware updates are available for your model, it may not always be possible to update directly from the current firmware version in your camera to the latest available version. In such cases, updates must be applied in stages. For this reason, it is recommended that, after updating the camera firmware, you immediately check again for additional updates. Simply repeat the update procedure to apply subsequent updates.
Does the SP-565 support the Olympus Wireless RC flash system?
The SP-565UZ supports the Wireless Flash system by which the camera's built-in flash acts as a controller that sends data commands to FL-36R and FL-50R electronic flash units that are set up off-camera.
The SP-565UZ controls only one group of flash units. The camera and flashes have four control channels to choose from so the flashes and camera will not receive signals from other Olympus wireless RC flash systems operating nearby. The photo below shows the main setup screen for the wireless RC flash system on the SP-565UZ set to Channel 2.
The flash group, channel and settings are then set up on the flash units. The SP-565UZ requires that Flash Group A is selected. When the camera shutter is tripped, the camera’s built-in flash emits a very high-speed burst of data in a pre-flash that commands the performance of the flash units.
The diagram below shows a sample placement of three flash units using the Olympus wireless RC flash system:
For details on the operation of the Olympus wireless RC flash system, please refer to the manuals for the FL-36R and FL-50R.
Olympus wireless RC flash system flashes, such as the FL-50R and the FL-36R can all be purchased from authorized Olympus dealers or online directly from The Olympus Store.
Does Olympus offer a remote cable release for the SP-565UZ?
The RM-UC1 Remote Cable Release (item #260237) is the electronic cable release for the SP-565UZ.
The RM-UC1 connects to the same USB port on the camera that is used to connect the camera to a computer via the bundled USB cable. The RM-UC1 has a sliding lock to lock the cable release for BULB exposures.
The RM-UC1 is available from authorized Olympus dealers and also online directly from The Olympus Store. To order the RM-UC1, click here.
Can I connect studio flash units to the SP-565UZ?
No. The SP-565UZ does not have a hot shoe or PC connector.
Does Olympus offer any conversion lenses for the SP-565UZ?
Olympus offers the TCON-17 Telephoto Conversion Lens for use with the SP-565UZ. The lens increases the magnification of the subject by 1.7x when the camera is at the extreme telephoto zoom. The CLA-10 Lens Tube Adapter, sold separately, is required to attach the TCON-17 to the SP-565UZ.
Both accessories are available from authorized Olympus dealers or online directly from The Olympus Store. To purchase the TCON-17 Telephoto Conversion Lens (Item #200862), click here. To purchase the CLA-10 Lens Tube Adapter (Item #202104), click here.
I want to use a lens filter with the SP-565UZ. What is the diameter of the filter thread?
The SP-565UZ does not have a filter thread; therefore, lens filters cannot be attached directly to the camera.
Filters with 55mm diameter can be attached to the SP-565UZ via the CLA-10 Lens Tube Adapter, sold separately. However, it is not recommended because vignetting may occur in the corners of the image when the camera is set to wide angle positions. Images taken with the SP-565UZ while using filters are not supported by Olympus.
The CLA-10 Lens Tube Adapter (Item #202104) is available from authorized Olympus dealers and also online from The Olympus Store. To purchase the CLA-10, click here.
When I look through the viewfinder, the image does not appear to be sharp. Why?
You may need to adjust the viewfinder's diopter to your vision. To the left of the viewfinder eyepiece cup is the diopter adjustment dial. While looking through the viewfinder, rotate the diopter adjustment dial until you can see the AF Frame clearly in the center of the viewfinder.
What is the orange "card" bundled with the camera, and how is it used?
The “card," pictured below as packaged, is the MASD-1 card adapter.
The MASD-1 accepts microSD and microSDHC media, giving owners the option to record to those cards or to xD-Picture Card media, which is Olympus’ preferred format.
To use microSD/SDHC media in the camera, simply insert the card into the adapter and then insert the adapter into the camera's memory card slot.Olympus maintains a list of supported microSD and microSDHC cards on its web site; click here to view it.
Will the bundled microSD™ adapter let me use any microSD or microSDHC card in my camera?
Click here to view a list of microSD and microSDHC cards that can be used with the MASD-1 card adapter. This page will be updated as additional cards are evaluated.
The PANORAMA feature does not function with microSD and microSDHC media. Also, the art editing features of the xD Pack plug-in for OLYMPUS Master 2 do not support images recorded to microSD/SDHC cards. To use these features, use Olympus brand xD-Picture Card media.
Will the microSD adapter allow me to use microSD and microSDHC media in other Olympus cameras?
MicroSD and microSDHC cards can be used only with cameras that are compatible with the MASD-1 microSD adapter. For a list of compatible cameras, click here.
The adapter is different from xD-Picture Card media in form. It will not fit in the card slots of other cameras that are compatible with xD-Picture Card media. Forcing the MASD-1 into an incompatible camera or other device may damage it or cause the equipment to malfunction. The data on the memory card may be destroyed.
I can't get a sharp image using Night Scene. What am I doing wrong?
The NIGHT SCENE and NIGHT+PORTRAIT Scenes are meant to take long exposures of skylines and city streets by leaving the shutter open for several seconds. Camera motion while the shutter is open causes blurriness. Therefore, it is necessary to stabilize the camera by bracing it against something solid or by using a tripod or camera clamp.
Sometimes when I'm shooting in dim light I have difficulty getting the camera to focus. What can I do?
Digital cameras autofocus by detecting differences in the contrast between light and dark areas of the image projected onto the sensor. If the light is dim or the image has a somewhat flat contrast, the camera may have difficulty focusing.
The SP-565UZ has an AF Illuminator feature that uses an LED to illuminate the subject just before the exposure is made, thereby assuring autofocus.
To enable the AF Illuminator:
- Press [MENU], select CAMERA MENU and then press [OK/FUNC].
- Using the down arrow button on the keypad, toggle down to AF ILLUMINATOR.
- Toggle right and select ON.
- Press [OK/FUNC].
- Exit the menu.
I went on vacation and used several memory cards. Now, when I'm downloading the images onto my computer and trying to save them, I get a message that says "Image file_name.jpg already exists.Replace it with the new file?" What's going on?
The SP-565UZ has two settings for creating file names for the images it captures:
- AUTO - Even when a new card is inserted, the folder numbers are retained from the previous card. If the new card contains an image file whose number coincides with one saved on the previous card, the new card’s file numbers start at the number following the highest number on the previous card.
Put simply, the camera picks up where it left off when naming files.
- RESET - When a new card is inserted, the folder numbers start at 100 and the file numbers start at 0001. If a card containing images is inserted, the file numbers start at the number following the highest file number on the card. If the card has been formatted, the file names will start with 0001.
Put simply, the card starts naming files anew beginning at 0001. At some point, the computer will start seeing duplicate numbers. When multiple cards are downloaded in this setting, each duplicate file name will have to be renamed individually or else the like-named files will overwrite their predecessors when they are saved to the computer. The original images will no longer be viewable.
When I try to select the PANORAMA option in the CAMERA MENU, the option is grayed out. Why?
The PANORAMA option in the SP-565UZ requires Olympus xD-Picture Card media to function.
When a series of images are shot while the SP-565UZ is in Panorama mode, the individual images are “tagged” with information that indicates they are elements of a panoramic image. This information is used to stitch the images together into an almost seamless single image.
The SP-570UZ provides three Panorama options:
- COMBINE IN CAMERA1 allows the photographer to shoot three images that are automatically stitched in camera and saved as one image on the memory card. After the first image is shot, a pointer (a red dot with crosshairs) is superimposed on the live view of the second image. As the camera is moved to the right, a white target mark moves into the image. When the pointer is centered on the target mark, the camera automatically takes a picture and saves it. The camera then places another pointer and target mark in the live view of the third image. When the pointer is centered on the target mark, the camera shoots the last picture and automatically initiates and completes the panoramic stitch, saving the final image on the memory card.
- COMBINE IN CAMERA2 allows the photographer to shoot three images freehand that are automatically stitched in camera and saved as one image on the memory card. This option superimposes blue lines to indicate overlap points for the stitch. Use of a tripod is recommended for this technique.
- COMBINE IN PC allows the photographer to shoot up to 10 images that can be imported into a computer and stitched together using OLYMPUS Master software. Again, a tripod is recommended for this technique.
My camera is connected to my TV with the video cable to playback my photos, but I don't see any images.
Televisions have AV (Audio/Visual) input channels (usually found below Channel 2) to play images and videos from digital cameras and camcorders. Using the TV channel selector, move downward through the channels until you see the camera menu on the TV screen. The display on the camera LCD screen or electronic viewfinder will be blacked out.
If the image quality on the screen appears to be distorted, the camera may be set to a video output format that is incompatible with the television. In the camera's SETUP menu, check the VIDEO OUT setting. In North America, the setting should be NTSC. If it is set to PAL, chnage it to NTSC.
How can I transfer images and movies from the camera to a computer?
Complete instructions may be downloaded by clicking here.
Adobe Reader® software is required to view the file. It is available as a free download from Adobe's web site. Click here to download the latest version.